User’s Manual
CTP150CM
7-Button Remote Control Panel
Contact Closure Control for the TPS150 Transmission System
Extron Electronics, USA
1230 South Lewis Street
Anaheim, CA 92805
USA
714.491.1500
Fax 714.491.1517
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
+31.33.453.4040
Fax +31.33.453.4050
Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Building
Singapore 368363
+65.6383.4400
Fax +65.6383.4664
Extron Electronics, Japan
Daisan DMJ Building 6F
3-9-1 Kudan Minami
Chiyoda-ku, Tokyo 102-0074 Japan
+81.3.3511.7655
68-994-01 Rev. A
Printed in the USA
05 04
Fax +81.3.3511.7656
© 2004 Extron Electronics. All rights reserved.
Table of Contents
Chapter 1 • Introduction ..........................................................1-1
About the CTP150CM ...........................................................1-2
Chapter 2 • Installation and Operation..........................2-1
Installation Overview .........................................................2-2
UL Requirements for Wall Box Installation..............2-3
Wall Mounting Site Preparation ....................................2-3
Wall Mounting .........................................................................2-6
Rear Panel Setup ...................................................................2-7
Front Panel Operation.........................................................2-8
Appendix • Reference Information.................................. A-1
Specifications ......................................................................... A-2
Parts List.................................................................................... A-3
Included parts........................................................................ A-3
Connected TPS150 transmission system.............................. A-3
Mini-AAP mounting options ................................................. A-3
Wall mounting solutions ................................................... A-3
Architectural solutions ....................................................... A-4
Table solutions .................................................................. A-4
Wall mounting hardware ..................................................... A-4
CTP150CM Remote Control Panel • Table of Contents
i
Table of Contents, cont’d
CTP150CM Remote Control Panel
Chapter One
1
Introduction
AbouttheCTP150CM
68-994-01 Rev. A
Printed in the USA
05 04
All trademarks mentioned in this manual are the properties of their respective
owners.
CTP150CM Remote Control Panel • Table of Contents
ii
Introduction
About the CTP150CM
CTP150CM Remote Control Panel
The Extron CTP150CM is a 7-button contact closure remote
control panel that can be connected to the TPT150 switching
transmitter of a TPS150 switching and transmission system
(figure 1-1). Each button corresponds to one of the
transmitter’s front panel functions and you can operate these
functions from the remote control panel or the TPT150
transmitter.
Extron
Control
System
TPR150
Twisted Pair
Receiver
z
H
3
-
6
7
;
4
A
5
.
2
0
;
C
A
V
0
6
-
2
0
9
:
T
R
O
P
P
1
8
c
U
S
2
1
0
.
7
L
A
-
7
1
Y
A
I
C
)
0
N
8
m
.
L
H
(
8
4
r
-
i
o
E
C
0
0
n
c
D
E
0
5
o
E
T
8
M
)
n
I
4
T
1
;
V
(
7
w
t
.
S
.
A
0
x
5
.
E
2
I
N
U
A
;
w
.
6
T
w
1
R
A
D
E
:
M
S
E
U
F
!
R
S
-
2
3
2
P
O
N
T
N
E
O
M
P
O
Y
C
T
U
P
U
T
O
O
-
Y
E
B
V
I
D
I
D
E
O
S
-
V
O
S
I
T
E
M
P
Extron
CTP150CM
Control
C
O
R
-
Y
A
VG
G
B
/
R
R
O
R
T
C
E
E
J
O
O
R
W
P
P
J
D
C
C
E
1
2
A
P
S
K
E
W
L
E
M
N
R
LU
P
L
I
N
K
G
O
V
U
T
E
P
UP
U
B
D
E
R
1
O
N
ID
W
V
V
O
D
Y
A
L
E
D
E
I
T
M
E
;
ID
V
0
5
2
;
A
6
.
1
:
E
S
U
F
:
T
R
O
P
P
U
7
S
2
7
1
0
o
RT
L
1
8
A
I
C
)
-
N
8
0
c
H
(
(
8
4
C
0
-
1
n
m
E
0
5
0
T
8
.
c
Panel
T
R
E
O
1
l
.
in
3
2
4
)
e
i
O
T
L
7
w
i
n
2
M
O
E
O
R
C
D
P
N
N
R
G
P
N
P
W
w
R
w
-
S
J
O
L
L
R
P
V
V
D
O
O
T
U
U
P
T
U
O
4
N
I
IO
D
3
2
1
U
N
N
N
A
I
I
I
+
-
R
L
K
IN
IO
D
L
U
T
P
A
U
-
L
-Y
4
R
+
T
U
P
IN
O
E
ID
V
IO
D
-
U
O
A
E
ID
V
S-
-Y
R
3
T
U
Chapter Two
P
IN
Y
TP
Cable
R
O
E
ID
V
IO
D
O
U
E
ID
A
2
T
-V
S
U
P
IN
A
Y
G
V
IO
B
G
/
D
U
R
A
L
1
T
U
P
IN
R
O
IT
N
R
O
M
L
T
A
U
C
P
O
T
L
U
O
A
G
V
Extron
/
B
G
R
Sound
System
TPT150
2
Switching
Transmitter
DVD
Component
Video
Input 4
Installation and Operation
VCR
Composite
Video
Input 3
PC
Input 1
Laptop
Input 2
Installation Overview
UL Requirements for Wall Box Installation
Wall Mounting Site Preparation
Wall Mounting
Figure 1-1 — CTP150CM as part of typical TPS150 system
The remote control panel is incorporated into a four space
mini-AAP enclosure that can be mounted into a variety of
Extron mini-AAP architectural options, including wall plates
(such as the CPM101), table-mounted connector bays (such as
the CPM208), or an interface or other device that has its own
mini-AAP mounting bays (such as the CIA111).
Rear Panel Setup
Front Panel Operation
CTP150CM Remote Control Panel • Introduction
1-2
Installation and Operation
Installation Overview
UL Requirements for Wall Box Installation
The following Underwriters Laboratories (UL) requirements
pertain to the installation of the CTP150CM into a wall or
furniture (figure 2-1).
Installation and service must be performed by
CAUTION
authorized personnel only. UL Listed electrical
boxes are recommended. See UL Requirements
for Wall Box Installation in this chapter.
Installation
Cable
Power off all devices and disconnect them from the
power source, if necessary.
1
2
Conduit
Run an 8-conductor cable between the site where the
CTP150CP control panel module will be installed and the
site of the TPT150 transmitter.
R
O
R
T
C
E
E
J
O
O
R
W
P
P
1
2
C
C
E
P
E
M
P
U
U
L
O
V
P
SHIFT
E
M
H.
1
2
U
W
O
L
O
N
O
V
VID
D
For installation in a wall or furniture, prepare the site:
cut a hole in the surface, install the electrical box or
mounting bracket, and prepare the cables. See Wall
Mounting Site Preparation in this chapter. See Mini-AAP
mounting options in appendix A, Reference Information, for a
partial list of devices that can accept four space mini-AAPs.
INPUT T
3
4
5
O
E
ID
V
MIN/MAX
1
2
2
IO
D
AU
Extron
™
MONITO
INPUT
INPUT
2
1
WITH ADSP
1
IO
D
U
A
CTP150CP
Remote Control
Panel
RGB 478 Mxi
OLLOWS
MONITOR
INPUT
1
Extron
RGB 478 Mxi
Interface
2.5"
For other installations, install a tabletop or in-table
connector bay, or other mini-AAP mounting option.
Refer to the manual for the device in which the control
panel module will be installed. See Mini-AAP mounting
options in appendix A, Reference Information, for a partial list
of devices that can accept four space mini-AAPs.
Figure 2-1 — CTP150CM in a four-gang wall box
1.
2.
These units must be installed in UL listed junction boxes.
These units must be installed with conduit in accordance
with the National Electrical Code.
Connect the 8-conductor cable between the remote
control panel and the transmitter. See Rear Panel Setup, in
this chapter for details.
Wall Mounting Site Preparation
The remote control panel can be mounted in a wall-mountable
four space mini-AAP A/V connector panel (such as a one-gang
CPM101) and then set into a wall with either a standard
stud-mounted wall box or with a wall mounting bracket
(IN9181). The remote control panel can also be mounted to any
wall-mountable Extron device that incorporates a four space
A/V mini-AAP connector panel, such as a three-gang RGB 468
Mxi. See Mini-AAP mounting options in Appendix A, Reference
Information, for a partial list of devices that can accept four space
mini-AAPs.
If the rear of the control panel module will be inaccessible
when the installation is complete, the operation of the
panel should be tested before the final mounting.
Apply or connect power to all devices in the system.
6
7
Test the system: Ensure that the transmitter responds as
desired to the remote control panel buttons. If necessary,
correct the system wiring. Ensure that you remove
electrical power if you need to change the system wiring.
Test the system again.
Choose a location that allows cable runs without interference.
Allow enough depth for the wall box and the cables. You
should install the cables in the wall or furniture, with or without
conduits, before installing the mounting bracket or wall box.
Mount the control panel module into any Extron four-
space mini-AAP connector panel.
8
9
Restore power to all devices.
The installation must conform to national and local electrical
codes and to the equipment’s size requirements.
CTP150CM Remote Control Panel • Installation and Operation
2-2
CTP150CM Remote Control Panel • Installation and Operation
2-3
Installation and Operation, cont’d
Installation using a UL listed wall box (available from Extron) is
5b. If you are using a wall box, insert the wall box into the
opening, and attach it to the wall stud or furniture with
nails or screws, leaving the front edge flush with the outer
wall or furniture surface (figure 2-3). The illustration
applies to both two-gang and four-gang wall boxes.
recommended for most mounting options, but the optional wall
mounting bracket can be used instead. All wall boxes must be
at least 1.0" (2.5 cm) deep.
Before using the wall mounting bracket, verify that the
installation conforms to national and local electrical
codes.
Wall Stud
Prepare the site as follows:
Installation
Cable
1.
If your wall box or mounting bracket includes a paper
template, cut out the indicated portions of the template.
If the wall box or mounting bracket does not include a
template, use the wall box or bracket itself to size the hole.
Cable Clamp
2.
Place the template, wall box, or mounting bracket against
the installation surface, and mark the guidelines for the
opening on the wall or furniture.
Screws or Nails
Wall opening
flush with
edge of box
3.
4.
Cut out the wall/furniture material from the marked area.
Check the opening size by inserting the wall box or
mounting bracket into the opening. The box or bracket
should fit easily into the opening. Enlarge or smooth the
edges of the opening if needed.
5a. If you are using a wall box, feed cables through the wall
box punch-out holes, and secure them with cable clamps to
provide strain relief.
Figure 2-3 — Attaching a wall box to a stud
If attaching the wall box to wood, use four #8 or #10
screws or 10-penny nails. A minimum of 1/2 inch (1.3 cm)
of screw threads must penetrate the wood.
Exposed cable shields (braids or foil) are potential sources
of short circuits. Trim back and/or insulate shields with
heat shrink (figure 2-2).
If attaching the wall box to metal studs or furniture, use
four #8 or #10 self-tapping sheet metal screws or machine
bolts with matching nuts.
Screw
Braided Shield
Metal Wall Box
Cable Clamp
Install Cable
Foil Shield
Figure 2-2 — Grounding outer braided and foil shields
To prevent short circuits, the outer foil shield can be
cut back to the point where the cable exits the cable
clamp. Both braided and foil shields should be
connected to an equipment ground at the other end
of the cable.
CTP150CM Remote Control Panel • Installation and Operation
2-4
CTP150CM Remote Control Panel • Installation and Operation
2-5
Installation and Operation, cont’d
6.
If you are using a mounting bracket, follow the directions,
if any, that came with the mounting bracket to attach the
clips that fasten the bracket to the wall or furniture (figure 2-4).
2.
3.
If not already accomplished, attach the 8-conductor cable
to the rear of the remote control panel.
Mount the CPM101 or other mini-AAP panel (with the
attached remote control panel) to the wall box or
mounting bracket using the two included mounting
screws (figure 2-5).
Wall
Figure 2-5 shows a wall box installation. Mounting the
mini-AAP panel to a mounting bracket is identical.
Extron
Push Mounting
Tabs Forward
IN9181 Wall
Mounting Bracket
4.
Power on all devices.
Rear Panel Setup
CONTACT
CLOSURE
Input 1
Input 2
Input 3
Input 4
GND
PROJ PWR
VOL DN
VOL UP
Figure 2-4 — Attaching a mounting bracket to a wall
1
Volume up
IN4
IN3
IN2
IN1
Volume down
Projector power
Ground
Wall Mounting
1.
Sandwich the mini-AAP panel (such as a CPM101)
CONTACT
CLOSURE
between the body of the remote control panel and the
printed front panel. Secure the front panel to the remote
control panel body with the included #4-40 screws
(figure 2-5).
GND
PROJ PWR
VOL DN
VOL UP
IN4
IN3
IN2
IN1
MADE IN USA
TPT150
Switching
Transmitter
CTP150CM Control Panel
Figure 2-6 — Rear panel view
Extron
CPM101
A/V Connector Panel
Contact closure connector — This connector is a 3.5 mm, 8-pole
captive screw connector for contact closure connections.
Connect a Category (Cat) 5 cable or any 8-conductor cable
between the remote control panel and the switching transmitter,
as shown in figure 2-6.
1
Wall opening
flush with
edge of box
OR
OJECT
PR WER
PO
PC
PC
1
2
UME
L
UP
VO
VIDEO
VIDEO
1
2
WN
DO
Extron
CTP150CM
Control Module
Front Panel
Figure2-5—Attachingthemini-AAPpaneltoawallbox
CTP150CM Remote Control Panel • Installation and Operation
2-6
CTP150CM Remote Control Panel • Installation and Operation
2-7
Installation and Operation, cont’d
Front Panel Operation
CTP150CM Remote Control Panel
The control panel (figure 2-7) emulates many front panel
controls of the TPT150 transmitter. See the TPS150 manual for
more details for each control.
PROJECTOR
POWER
PC 1
PC 2
1
1
1
1
2
VOLUME
UP
VIDEO 1
VIDEO 2
3
3
DOWN
Figure 2-7— Front panel
Input select buttons — The PC 1, PC 2, Video 1, and Video 2
buttons select video and audio inputs 1 through 4 on the TPT150
transmitter.
1
2
Appendix
A
Projector Power button — The Projector Power button
commands the TPT150 transmitter to issue the projector power
on or off command. See the TPS150 manual, chapter 4, Serial
Communications, to specify the command(s) to be sent.
Volume Up and Down buttons — The Volume Up and Down
buttons command the TPT150 transmitter to increase and
decrease the output volume and input level.
3
Reference Information
Output volume —
Specifications
Parts List
Press and release the Volume Up or Down button to increase or
decrease the output volume by 1 dB per push of the button or
press and hold the button to ramp the output volume up or
down.
Input audio level —
1.
2.
Press and hold the desired input select button.
While you continue to hold the Input Select button, press
and release the Volume Up or Down button to increase or
decrease the selected input’s volume or press and hold the
button to ramp the selected input’s volume up or down.
3.
Release the input select button.
CTP150CM Remote Control Panel • Installation and Operation
2-8
Reference Information
Specifications
Parts List
Included parts
Control/remote — TPS150
Contact closure ............................ (1) 3.5 mm captive screw connector, 8 pole
Description
Part number
Contact closure pin configurations 1 = input 1, 2 = input 2, 3 = input 3,
4 = input 4, 5 = volume up,
CTP150CM (black)
60-614-10
60-614-20
10-265-05
or
CTP150CM (white)
6 = volume down, 7 = projector power,
8 = GND
8-pole captive screw connector
Tweeker (small screwdriver)
1/16" hex wrench
General
Temperature/humidity .............. Storage -40° to +158°F (-40° to +70°C) /
10% to 90%, noncondensing
CTP150 Control Panel Module manual
Operating +32° to +122°F (0° to +50°C) /
10% to 90%, noncondensing
Connected TPS150 transmission system
Rack mount .................................. No, but furniture mountable with an
optional CPM Series faceplate
Enclosure type .............................. Metal
Enclosure dimensions
Description
Part number
TPS150
70-369-01
Mini-AAP mounting options
Faceplate ................... 2.8" H x 2.2" W x 0.1" D
(7.1 cm H x 5.6 cm W x 0.3 cm D)
(four space MAAP)
Device ........................ 2.8" H x 2.2" W x 0.5" D
(7.1 cm H x 5.6 cm W x 1.3 cm D)
Wall mounting solutions
Description
Part number
CPM101B (one-gang) (black)
60-583-11
60-583-21
60-583-12
60-583-22
(Depth excludes connectors and buttons.)
Product weight ............................. 0.5 lbs (0.3 kg)
Shipping weight ........................... 1 lbs (1 kg)
Vibration ....................................... ISTA 1A in carton
(International Safe Transit Association)
Listings .......................................... ETL(UL1950)
Compliances ................................. CE
CPM101W (one-gang) (white)
CPM102B-1 (two-gang) (black) with cable guards
CPM102W-1 (two gang) (white) with cable guards
CPM102B-2 (two-gang) (black) without cable guards 60-583-13
CPM102W-2 (two-gang) (white) without cable guards 60-583-23
CPM103B-1 (three-gang) (black) with cable guards
CPM103W-1 (three-gang) (white) with cable guards
60-583-14
60-583-24
MTBF ............................................. 30,000 hours
Warranty ....................................... 3 years parts and labor
CPM103B-2 (three-gang) (black) without cable guards 60-583-15
CPM103W-2 (three-gang) (white) without cable guards 60-583-25
All nominal levels are at 10%
CPM104B-1 (four-gang) (black) with cable guards
CPM104W-1 (four-gang) (white) with cable guards
60-583-16
60-583-26
Specificationsaresubjecttochangewithoutnotice.
CPM104B-2 (four-gang) (black) without cable guards 60-583-17
CPM104W-2 (four-gang) (white) without cable guards 60-583-27
CTP150CM Remote Control Panel • Reference Information
A-2
CTP150CM Remote Control Panel • Reference Information
A-3
Reference Information, cont’d
Architectural solutions
Description
Part number
RGB 468 Mxi (black)
60-591-02
60-591-03
60-596-12
60-596-13
60-596-22
60-596-23
60-592-02
60-592-03
RGB 468 Mxi (white)
CIA111 (black, with cable guards)
CIA111 (white, with cable guards)
CIA111 (black, without cable guards)
CIA111 (white, without cable guards)
RGB 478 Mxi (black)
RGB 478 Mxi (white)
Table solutions
Description
Part number
CPM208-1 Mini-AAP bay
60-589-13
60-590-11
60-590-21
60-639-02
CPM212-1 Tabletop mini-AAP bay (black)
CPM212-2 Tabletop mini-AAP bay (white)
Surface mount box, one-gang
Wall mounting hardware
Description
Part number
One-gang “J” box, 2.5” deep
Two-gang “J” box, 2.5” deep
Three-gang “J” box, 2.5” deep
Four-gang “J” box, 2.5” deep
One-gang mounting bracket
980130
980084
980083
980097
IN9181
A-4
CTP150CM Remote Control Panel • Reference Information
|